Nitrocellulose Sanding Sealer Hi-build 

Note: because we buy in and decant off this  product the container  may come un-branded  

Note Post Listed is for North Island Only please email for a quote if in the South Island 

Multi purpose sanding sealer

Sanding Sealer 1/2 Litre   New economy size tins  $24.50

Sanding sealer 1 litre $32.50

Sanding Sealer 4 litre $115.00 Post Quoted

Use Thinners LT1 (spray thinners)

To seal timber thin by up to 50%.

Then sand with the same grit you used before applying the sealer.

Apply a 2nd coat and sand through the grits.

Lacquer or wax can then be applied as the finish.

Ideal to lock up that end grain on wooden bowls and craft items so that oils dont darken the end grain .

4l Litre Freight will be quoted  please email us

 LT1 932 Sanding Sealer

PRODUCT DESCRIPTION & USES
932 Sanding Sealer is a clear, quick drying, modified nitrocellulose wood sealer. It does not contain an organic sanding
aid, and is therefore suitable under pre-catalysed lacquers without ‘bloom’ problems.
932 Sanding Sealer shows excellent sealing and lacquer hold out properties. It is a modified nitrocellulose one pack
sealer for use on timber, hard board, plywood and furniture. With quick dry and cure times Sanding Sealer displays
excellent sanding qualities and is suitable for over-coating with 936 Pre Catalysed Lacquers.
A premium quality Nitrocellulose Sealer for manufactured boards. 930 Customwood Sealer has been formulated to
resist the inhibition of dry arising from the waxes or oils present in most processed timber boards.
932 Sanding Sealer should not be used to seal oily timbers such as Rimu, Matai or Totara. On these timbers 772
Portco 2K Sealer is recommended.

PRODUCT FEATURES
Fast drying
Good holdout ensuring even gloss of finish coats of lacquer.
Excellent colour development on dark or dark stained timber.
Crisp sanding character.
Supplied ready for use.
Made in New Zealand for New Zealand manufactured boards and conditions.
TECHNICAL DATA
Gloss Level Low sheen.
Primer Not applicable.
Wash Up 002-000 LT1
Colours Clear.
Pack Size 4L, 20L.
Storage Temperature 5 C - 50 C
Shelf Life Minimum 2 years.
Toxicity Formulated without added lead or mercury. Dried sealer is non-toxic. Suitable for use on toys
or items that may be chewed.
VOC content 707g/L for Clear as per EC-07-09 and APAS definition of Volatile Organic Compound.
Volume Solids 14.7%
Wet Film Thickness 85 to 125µ
Dry Film Thickness 12 to 18µ
Coverage 8-12 m²/L.
SUBSTRATE PREPARATION INSTRUCTIONS
General Surface Preparation: Surfaces must be clean of all traces of grease, wax, oil or silicone. Sand timber smooth
with 180-240 grit dri-lube abrasive paper prior to staining.
Fill any holes and minor imperfections with a suitably coloured timber putty before staining.
Stain, if required, with 935 NGR Stain or 768 Wiping Stain.
RECOMMENDED APPLICATION METHODS AND TECHNIQUES
Stir thoroughly before use, ensuring any settled sanding aid is evenly stirred in.
Thin, if required for ease of application to a maximum of 10% by volume with 002-000 LT1 Thinners.
Apply a double header coat wet on wet by spray to give a wet film thickness of 85-125µ. Allow to dry and sand with
320-400 grit dri-lube paper.
Better holdout will be achieved if the sealer is allowed to dry overnight before top coating.
Finish with 936 Precat Lacquer in the sheen level of your choice.
932 Sanding Sealer
Date Issued: 04 November 2014; Reason for Issue: New Format; Version: 1.0; Replaces Version: 29 July 2013; Page 2 of 2
NOTE: The information concerning the use and application of this product is intended for use by professional specifiers and applicators, is given in good faith and is believed to be
correct at the date of issue. Protective Paints Ltd reserves the right to alter the product or specification without notice. The user should check the date of issue, and if more than 24
months have elapsed, should verify with our nearest sales office that the information is still current. Because we cannot control the way these products may be used, or the conditions
they may be exposed to, we can give no express guarantees in respect of the performance of this product. However certain guarantees may be implied by law.
Protective Paints Limited, 14 Arwen Place, East Tamaki, P.O. Box 204 293, Highbrook Postal Centre, Manukau 2161
Ph: (09) 274 5606 Ph: 0800 724 684 Fax: (09)274 0940. Email: reception@propaints.co.nz
http://www.propaints.co.nz/; http://www.portugalcork.co.nz/; http://www.paintndecor.co.nz/
Note: Do not exceed a dry film build of 150µ for Sealer and finish coat, or 5 generous double header spray applications,
or stress cracking of the finish on aging may result.
Minimum Surface Temperature: 5 C
Maximum Relative Humidity: 95%
Temperature Range: 5 C - 35 C
Suitable Application Methods: Spraying.
Thinners: 002-000 LT1 Thinners
Cleaning Solvent: 002-000 LT1 Thinners
Max. Volume Thinners: 10%.
Conventional Spray: Fluid nozzle: 1.5 – 2.0mm, Pressure to the gun: 210 – 350kPa (30 – 50psi)
Airless Spray: Fluid nozzle: 9 – 11 thou, Pump ratio: 16:1 to 20:1, Pump pressure: 7,000 –
10,000kPa (1000 – 1500psi).
DRYING CHARACTERISTICS
All figures quoted are at 20 C and 65% relative humidity.
Drying will take longer at lower temperatures and/or at higher relative humidity.
Do not stain when temperature of surface is below 5 C or above 35°C.
Touch Dry: 30 minutes
Dry to sand: 1 hour
Recoat: Can be finished after 1 hour, but for maximum hold-out let the sealer dry for 16 hours prior to
recoating.
HEALTH & SAFETY
CAUTION! FLAMMABLE
Contains petroleum solvents: keep away from heat and open flame. Close container when not in use.
KEEP OUT OF REACH OF CHILDREN
WARNING: This material may be harmful if swallowed or inhaled and may cause skin or eye irritation.
PRECAUTIONS: Avoid breathing vapour -- use with adequate ventilation. Do not eat, drink, or smoke whilst using. Store
in a cool, well ventilated area indoors between 5°C - 20°C. Dispose of empty container safely. Empty cans or cans
containing dry material may be recycled. Do not contaminate any water supply.
FIRST AID
If Swallowed: Give water to dilute. Owing to the aspiration hazard of hydrocarbon solvents, DO NOT CAUSE VOMITING.
Get medical attention without delay.
Eye Contact: Treat immediately with water -- hold open and flush for at least 15 minutes. Get medical attention if irritation
persists.
Skin Contact: Remove any contaminated clothing and wash skin thoroughly with soap and water. Avoid scrubbing skin.
Inhalation: Leave the hazard area, maintain breathing and get medical attention.
FIRE: Use foam, carbon dioxide or dry chemical powder.
SPILLS: Absorb with sand or earth. Collect and seal in properly labelled drums for disposal according to local waste
management authority.
Refer MSDS, available on request, for detailed safety instructions.