Loading... Please wait...

Categories

Our Newsletter


Gemcoat casting resin epoxy 2:1 1.5ltr kit

  • Image 1
  • Image 2
Price:
$95.50
SKU:
Gem4.151
Weight:
2.00 KGS
Shipping:
$12.80 (Fixed shipping cost)
Quantity:
Bookmark and Share


Product Description

Gemcoat casting resin epoxy 2to1 1.5l kit                              Timberly New Zealand Agent

Wanting to add inlays to your woodturning or joinery

Suitable for table tops

Then this non-yellowing crystal clear reason is what I’d suggest to inlay the likes of shells,

or any other medium that will enhance your turning.

Alby Halls Pieces from the Ancient Kauri Kingdom have always enticed concerning buyers.

This is the product he uses

Composition and Properties

• GEMCOAT ES 2:1 LV is a low viscosity epoxy resin formulated for use as a hard, resistant,
clear sealer for timber and other substrates (consult GemCo).
• It is particularly suited to filling cavities up to 20mm deep in one pour due to its air release &
low viscosity
Physical properties
• Appearance: Base - clear liquid
Hardener - clear liquid
• Odour: low odour
• Flammability: non flammable
• Solids: 100%
• Coating Type: Epoxy
• Packaging: 1.5L,6L, 30 litre two part pack & 200L drums
• Mix ratio: 2:1(base : hardener)
• Pot Life: Approximately 30 min @ 20 °Celsius (200g mix)
Coverage: 1 sq metre/litre @ 1 mm thickness ( typical - depends on substrate)
• Dry to Recoat: Typically overnight - will vary according to temperature &
humidity.
• Tensile strength:* 3000 psi
• Compressive strength* 7000 psi
• Shore hardness:* 70
*typical value
Preparation
• A test patch is recommended on a new substrate or if the product has not been used before.
• All surfaces to be clean, dry, and free of loose material
• Thoroughly solvent wipe wooden surfaces to remove any oily deposits and allow to dry.
Application
• For best results store , apply, & cure resin at temperature of 25 ° C.
• Add 1 part hardener to 2 parts base (by volume) and thoroughly hand mix .
• Hand mix small quantities with a stick taking care to scrape sides & bottom of container then
allow to sit for a few minutes for air to come out - watch pot life.
• Pour in to cavity to be filled and leave product to self level then use a gas flame or heat gun (if
required) waved gently over the surface to release any air bubbles.
• Allow to cure in a dust free environment. The product can be cut and polished although the
finish is often good enough without this.
• Cutting & Polishing - wet sand with 600 then 1200 grit paper until a uniformly flat surface is
achieved. Buff with 3M Perfect It III 5958 cutting compound (or equivalent) until level of gloss
required is achieved. A coat of 3M Perfect-It III polish (or equivalent such as Diamond Cutting
Compound 2.0) can be applied to give a very high gloss finish.
• Note: GEMCOAT ES 2:1 LV can be used on bar & table tops but GEMCOAT ES 1:1 is
better suited to this type of use
Handling Precautions
• Avoid contact with eyes and skin. Do not ingest. Use with adequate ventilation.
• Protective clothing , eye protection, and gloves should be worn. Keep away from children.

 

 

For Insttuctions down load Here :

http://bit.ly/2q5zjPP

 

 

 

 

 

 


Write your own product review

Product Reviews

This product hasn't received any reviews yet. Be the first to review this product!


Add to Wish List

Click the button below to add the Gemcoat casting resin epoxy 2:1 1.5ltr kit to your wish list.

You Recently Viewed...